Lifting Solution Specialist

Polyester Round Sling EN 1492-1/AS 4497

Home  Products  >  Textile Lifting Sling  >  Polyester Round Sling to EN 1492-2/AS 4497

Polyester Round Sling EN 1492-2/AS 4497
Polyester Round Sling
Round Sling 3t
Type 
-Polyester round sling to EN 1492-2 & AS 4497

Technical specifications 
-Colour coded according to EN 1492-2 & AS 4497 
-Capacity stripes; each stripe is equal to 1 tonne capacity.
-The safe working load is clearly and continuously printed on the sleeve (upon request). 
-Extra strong PU-impregnated webbing of the sleeve, which does not allow dirt to enter. 
-Each sling is packed in plastic with CE declaration of conformity or Test Certificate (upon request). 

Characteristics: 
-Low elongation.  
-Extremely wear-resistant. 

Norms 
-According to Machinery Directive 2006/42/EC, EN 1492-2 & AS 4497 
-Safety Factor: 7:1

 

Round slings are an all-purpose lifting sling enabling a strong and non-damaging lift of a load. They are extremely light weight and flexible in multiple directions, allowing easy and quick manipulation even when fragile loads are being lifted. Round slings are a continuous loop made from polyester yarn encased in a sleeve of polyester fabric. The sleeve is constructed, so that it protects the internal rows of yarn filament and keeps them in a parallel formation at all times. The yarn fibre (core) is free to spread out where the round sling is in contact with its load. This provides a broad support, which cushions the load against damage and reduces slipping. The low stretch characteristics of the polyester yarn also prevent ‘load bounce’ when lifting.

Roundsling
When ordering it is important to make clear whether the length specified is circumference or effective working length(EWL).

Item

Colourcoded
according to
EN1492-2

Working Load Limit with 1 round sling

Working Load Limit with 2  
round slings

Straight
lift

Chocked
  lift

0-7

Straight
lift up to 45
Choked
lift up to 45
Straight
lift
45-60
Choked
lift
45-60
0-7 7-45 45-60 45-60
1.0

0.8

2.0
1.4
1.0
0.7
0.5

1.4

1.12
1.0
0.8
RSEL-01 WLL 1T
1.000
800
2.000
1.400
1.000
700
500
1.400
1.120
1.000
800
RSEL-02 WLL 2T
2.000
1.600
4.000
2.800
2.000
1.400
1.000
2.800
2.240
2.000
1.600
RSEL-03 WLL 3T
3.000
2.400
6.000
4.200
3.000
2.100
1.500
4.200
3.360
3.000
2.400
RSEL-04 WLL 4T
4.000
3.200
8.000
5.600
4.000
2.800
2.000
5.600
4.480
4.000
3.200
RSEL-05 WLL 5T
5.000
4.000
10.000
7.000
5.000
3.500
2.500
7.000
5.600
5.000
4.000
RSEL-06 WLL 6T
6.000
4.800
12.000
8.400
6.000
4.200
3.000
8.400
6.720
6.000
4.800
RSEL-08 WLL 8T
8.000
6.400
16.000
11.200
8.000
5.600
4.000
11.200
8.960
8.000
6.400
RSEL-10 WLL 10T
10.000
8.000
20.000
14.000
10.000
7.000
5.000
14.000
11.200
10.000
8.000
RSEL-12 WLL 12T
12.000
9.600
24.000
16.800
12.000
8.400
6.000
16.800
13.400
12.000
9.600

ALWAYS: 
• Store and handle roundslings correctly. 
• Inspect roundslings and accessories before use and before placing into storage. 
• Follow safe slinging practices, as given overleaf. 
• Position the bight for choke lift at 120°(natural angle). 
• Apply correct mode factor for the slinging arrangement. 
• Use protection (to avoid cutting, friction etc) and fittings which allow the sling to form smooth radii.


NEVER: 
• Attempt to shorten, knot or tie roundslings. 
• Expose roundslings to direct heat or flames. 
• Use roundslings at temperatures above 80°C or below 0°C without consulting the supplier. 
• Expose roundslings to chemicals without consulting the supplier. 
• Shock load roundslings. 
• Use roundslings with cut or damaged outer covers. 
• Use a sling with a missing/damaged label or illegible markings


Selecting the Correct Sling 
Roundslings are available in a range of materials and sizes in endless sling form. Select the slings to be used and plan the lift taking the following into account: 
Material – polyester, identified by a blue label, is resistant to moderate strength acids but is damaged by alkalis; polyamide (Nylon) identified by a green label, is virtually immune to alkalis but is damaged by acids; polypropylene, identified by a brown label, is little affected by acids or alkalis but is damaged by some solvents, tars and paints and therefore suitable for appliances where the highest resistance to chemicals other than solvents is required. 
Capacity - the sling must be both long enough and strong enough for the load and the slinging method. 
Apply the mode factor for the slinging method. 
For use at temperatures exceeding 80°C or below 0°C refer to the suppliers instructions. 
For round slings made to BS EN 1492-2:2000 + A1: 2008 * 
Polyester and Polymide -40ºC to 100ºC Proypropylene -40ºC to 80ºC Ranges vary in a chemical environment, in which case the advice of the manufacturer or supplier should be sought. 
If the slings are to be used in multi-leg arrangement the angle formed between the legs should not be less than 30° or greater than 90°. 
If abrasion, heat generated by friction or cutting from edges or corners which may damage the sling are likely, select a sling fitted with additional protective sleeves and/or use suitable packing. 
Slings with grade 8 fittings and multi-leg master links should not be used in acidic conditions. Contact with acids or acidic fumes causes hydrogen embrittlement to grade 8 materials. If exposure to chemicals is likely, the manufacturer or supplier should be consulted.


Storing and Handling Roundslings 
Never return wet, damaged or contaminated slings to storage. They should be cleaned with clear water and dried naturally. Never force dry roundslings. 
Store roundslings by hanging on non-rusting pegs which allow the free circulation of air. 
The storage area should be dry, clean, free of any contaminates and shaded from direct sunlight. 
Do not alter, modify or repair a roundsling but refer such matters to a Competent Person.


NOTE: The material from which the roundsling is manufactured may be identified by the colour of the label or printing on the label: Polyester = Blue, Polyamide (Nylon) = Green, Polypropylene = Brown. The outer sleeve of the sling will also be colour coded to indicate the SWL in straight pull.


Using Roundslings Safely 
Do not attempt lifting operations unless you understand the use of the equipment, the slinging procedures and the mode factors to be applied. 
Do not use defective slings or accessories. 
Check for correct engagement with fittings and appliances, ensuring smooth radii are formed which allow the sling to assume its naturally flattened form under load. Do not overcrowd fittings. 
Position the bight for a choke lift at the natural (120°) angle to prevent friction being generated. 
Keep labels away from hooks and fittings. 
Take the load steadily and avoid shock loads. 
Do not leave suspended loads unattended. In an emergency cordon off the area.


In-service Inspection and Maintenance 
Maintenance requirements are minimal. Roundslings may be cleaned with clear water. Remember weak chemical solutions will become increasingly stronger by evaporation 
Before each use inspect roundslings and, in the event of the following defects, refer the sling to a Competent Person for thorough examination: illegible markings; damaged or cut outer cover; damaged stitching; exposed inner core; heat damage; burns; chemical damage.