H-LIFT INDUSTRIES CO LTD
          About us       |       Products      |        Service       |       Contact us      |        Sitemap www.h-lift.com
     Products>>G-80 Alloy Chain  |  G-80 Chain Sling  | G-80 Alloy Fittings  |   G-100 Alloy Fittings  |

  

  Product Categories

 

w    

 

 

 

 

G-80 Lifting Chain, Black G-80 Lifting Chain, Painted G-80 Lifting Chain, Zinc Plated

grade 80 chain, G-8 chain, grade 100 lifting chain, sling chain, chain sling, G-8 alloy chain, chain hoist, lashing chain

 

grade 80 chain, G-8 chain, grade 100 lifting chain, sling chain, chain sling, G-8 alloy chain, chain hoist, lashing chain

 

 

grade 80 chain, G-8 chain, grade 100 lifting chain, sling chain, chain sling, G-8 alloy chain, chain hoist, lashing chain

 

G-80 LASHING CHAIN
 

ITEM NO
CHAIN
SIZE
LINK DIMENSION
TEST
LOAD
BREAKING
LOAD Min.
WEIGHT
PER M
S(DIA.)
R(I.L)
F(I.W.)
MM
MM
MM
MM
KN
KN
KG
G8L0635
6
6
35
22
22
44
0.64
G8L0953
9
9
53
33
49
98
1.42
G8L1164
11
11
64
40
73.5
147
2.18
G8L1380
13
13
80
48
95
190
3.01

 

grade 80 chain, G-8 chain, grade 100 lifting chain, sling chain, chain sling, G-8 alloy chain, chain hoist, lashing chain

 

Definitions to European standard EN 818-7

 

For the purposes of this Part of EN 818,the following definitions apply:

1. nominal size:  Nominal diameter of the round section steel wire or bar from which the chain is made.
2. material diameter: Diameter of the material in the chain link as measured.
3. weld diameter: Diameter at the weld as measured.
4. length dimensionally affected by welding: Length on either side of the center of the link, affected by welding.
5. pitch: Internal length of a link as measured.
6. manufacturing proof force(MPF) of chain: Force to which during manufacture the whole of the chain is subjected.
7. breaking force( BF): Maximum force which the chain withstands during the course of a static tensile test to destruction.
8. working load limit (WLL) of chain: Maximum mass which the chain hanging vertically is authorized to sustain in general lifting service.
9. total ultimate elongation (A): Total extension at the point of fracture of the chain expressed as a percentage of the internal length of the test sample.
10. processing: Any treatment of the chain subsequent to welding, for example, heat treatment, polishing or dimension calibration.
11. lot: Specified quantity from which test sample(s) is/are selected.
12. competent person: A designated person, suitably trained qualified by knowledge and practical experience, and with the necessary instructions to enable the required examination to be carried out.

 

       Products>>G-80 Alloy Chain  |  G-80 Chain Sling  | G-80 Alloy Fittings  |   G-100 Alloy Fittings  |

       About us  |  Products  |  Service  |   Contact us  |  Sitemap www.h-lift.com
 Copyright @ 2017 H-Lift Industries Co.,Ltd. All rights reserved
8/F., No. 560 Jincheng Road, Xiaoshan, Hangzhou, 311202, China
Tel: +86-571-8263-6008, 8263-6018, 8263-6058, 8263-6068
Fax: +86-571-8263-6028 E-mail: info@h-lift.com